Results 1 to 5 of 5
- 10-10-2004, 06:05 PM #1LanningGuest
Settings - Sounds - Ringer Type - Voice Calls - With Caller ID.
All ringer tones can be heard and selected, but are not saved.
When backing out of the menu five dots are displayed instead of a selected
tone.
I got the phone at the very introduction of the model, but the firmware is a
newer version (1.56SP).
Thanks very much for any advice.
Roy Lanning
› See More: Sanyo 4900 does not ring if the caller has Caller ID.
- 10-11-2004, 05:46 AM #2Bob SmithGuest
Re: Sanyo 4900 does not ring if the caller has Caller ID.
"Lanning" <[email protected]> wrote in message
news:T6kad.22272$cJ3.17303@fed1read06...
> Settings - Sounds - Ringer Type - Voice Calls - With Caller ID.
>
> All ringer tones can be heard and selected, but are not saved.
>
> When backing out of the menu five dots are displayed instead of a selected
> tone.
>
> I got the phone at the very introduction of the model, but the firmware is
a
> newer version (1.56SP).
>
> Thanks very much for any advice.
>
> Roy Lanning
On my 5300, it shows the same 5 dots, but the specific ringer is saved.
Those five dots are telling you that there are multiple options available in
the setting.
Bob
- 10-11-2004, 01:53 PM #3LanningGuest
Re: Sanyo 4900 does not ring if the caller has Caller ID.
"| > Settings - Sounds - Ringer Type - Voice Calls - With Caller ID.
| >
| > All ringer tones can be heard and selected, but are not saved.
| >
| > When backing out of the menu five dots are displayed instead of a
selected
| > tone.
| >
| > I got the phone at the very introduction of the model, but the firmware
is
| a
| > newer version (1.56SP).
| >
| > Thanks very much for any advice.
| >
| > Roy Lanning
|
| On my 5300, it shows the same 5 dots, but the specific ringer is saved.
| Those five dots are telling you that there are multiple options available
in
| the setting.
|
| Bob
Thanks, Bob, but it used to show the chosen ringer. And, why wouldn't "No
Caller ID" and "Roaming" (which also have choices) show dots, too?
Roy
- 10-11-2004, 04:19 PM #4Bob SmithGuest
Re: Sanyo 4900 does not ring if the caller has Caller ID.
"Lanning" <[email protected]> wrote in message
news:SwBad.28892$cJ3.25840@fed1read06...
> "| > Settings - Sounds - Ringer Type - Voice Calls - With Caller ID.
> | >
> | > All ringer tones can be heard and selected, but are not saved.
> | >
> | > When backing out of the menu five dots are displayed instead of a
> selected
> | > tone.
> | >
> | > I got the phone at the very introduction of the model, but the
firmware
> is
> | a
> | > newer version (1.56SP).
> | >
> | > Thanks very much for any advice.
> | >
> | > Roy Lanning
> |
> | On my 5300, it shows the same 5 dots, but the specific ringer is saved.
> | Those five dots are telling you that there are multiple options
available
> in
> | the setting.
> |
> | Bob
>
> Thanks, Bob, but it used to show the chosen ringer. And, why wouldn't "No
> Caller ID" and "Roaming" (which also have choices) show dots, too?
>
> Roy
Don't have a clue why that wouldn't show up. You are on a an older firmware.
Current version is 1.059 SP. You will need to go to your local SPCS store to
get that firmware loaded up and that might fix the problem. If it doesn't,
ask the local folks whether they have any 4900's in stock and see if you can
swap it out, after transferring your ringers, etc.
Bob
- 10-12-2004, 06:22 AM #5LanningGuest
Re: Sanyo 4900 does not ring if the caller has Caller ID.
"Bob Smith" <[email protected]> wrote in message
news:[email protected]...
|
| "Lanning" <[email protected]> wrote in message
| news:SwBad.28892$cJ3.25840@fed1read06...
| > "| > Settings - Sounds - Ringer Type - Voice Calls - With Caller ID.
| > | >
| > | > All ringer tones can be heard and selected, but are not saved.
| > | >
| > | > When backing out of the menu five dots are displayed instead of a
| > selected
| > | > tone.
| > | >
| > | > I got the phone at the very introduction of the model, but the
| firmware
| > is
| > | a
| > | > newer version (1.56SP).
| > | >
| > | > Thanks very much for any advice.
| > | >
| > | > Roy Lanning
| > |
| > | On my 5300, it shows the same 5 dots, but the specific ringer is
saved.
| > | Those five dots are telling you that there are multiple options
| available
| > in
| > | the setting.
| > |
| > | Bob
| >
| > Thanks, Bob, but it used to show the chosen ringer. And, why wouldn't
"No
| > Caller ID" and "Roaming" (which also have choices) show dots, too?
| >
| > Roy
|
| Don't have a clue why that wouldn't show up. You are on a an older
firmware.
| Current version is 1.059 SP. You will need to go to your local SPCS store
to
| get that firmware loaded up and that might fix the problem. If it doesn't,
| ask the local folks whether they have any 4900's in stock and see if you
can
| swap it out, after transferring your ringers, etc.
|
| Bob
|
OK. Either would be better than having to buy a new phone which is what I
had expected. Thanks.
Similar Threads
- alt.cellular.verizon
- LG
- alt.cellular.sprintpcs
- alt.cellular.motorola
- Samsung
Mercado para la venta de autos.
in Chit Chat