Results 1 to 2 of 2
  1. #1
    ProgDario
    Guest
    HI,

    Phone model: Nokia 5510
    Cable: original DKE-2 cable.

    I read that with this cable I can ONLY upload music.

    So I bought an FBUS cable, that connects via USB and emulates a COM
    port.

    With Oxygen it doesn't work, it says "COM 3: Phone is not found".

    Can I use DKE-2 to transfer data or do I have to use only the FBUS
    cable?


    Thanks


    Dario




    See More: How to use DKE-2 cable??




  2. #2
    Oxygen Software
    Guest

    How to use DKE-2 cable??

    Regarding problems with F-Bus USB cable connection:

    >With Oxygen it doesn't work, it says "COM 3: Phone is not found".


    1) Do you have any switches on your cable? If yes, you should switch the
    cable to F(F-Bus) mode.

    2) The cable's PIN contacts have to be of the same length and none of them
    may stuck in cable's contact platform. Is it true? If not, then the cable is
    defective.

    3) Have you removed isolating foam around the cable's PIN contacts? Please
    remove this, as the foam may block cable contacts.

    4) Please, check, whether you have placed the battery to corresponding
    battery holders (slots) in the cable's contact platform.

    5) Is the phone turned on, while trying to establish connection? The phone
    has to be turned on, so the signal could reach the phone.

    6) What settings have you checked in our Program? Working settings are:
    'COM3' (in your case) checked and set as 'DAU-9p/F-Bus' , 'Infrared' - not
    checked, 'Bluetooth'- not checked, 'DKU-5/CA-42' - not checked, 'DKU-2' -
    not checked, all other virtual COM ports- not checked.

    7) Please make sure that cable connection is turned off in Nokia Connection
    Manager ( 'Start' -> 'Settings' -> 'Control panel' -> 'Nokia Connection
    Manager' ). If the cable connection is turned on in Nokia Connection
    Manager, then our program won't pick the phone up even if it is successfully
    connected.

    8) Please, set virtual COM port's speed to '115200 bit/s' in 'Start' ->
    'Settings' -> 'Control panel' -> 'System' -> 'Hardware' -> 'Device
    manager' -> 'Ports COM and LPT' -> right-click once on COM3 ->
    'Properties' -> 'Advanced' ( 'General' or 'COM port settings' - the name
    depends on driver version). Here you should set COM port's speed to 115200
    bit/s.

    9) Make sure, you are using the latest version ( 2.8.3.3 ) of our software.
    You can view version number in 'Help' -> 'About' . You can download the
    latest trial version here: http://www.opm-2.com/download/opm2.zip

    If you have any questions and/or suggestions, concerning our
    program, feel free to post them on our official forum
    http://www.opm-2.com/forum/

    Best regards, Maxim Vyalkov
    Oxygen Software - tools for your mobile phone.
    Oxygen Phone Manager II - all you want from your mobile phone.
    http://www.oxygensoftware.co.uk/
    http://www.smsactivex.com/

    Hello, ProgDario!
    You wrote in conference alt.cellular.nokia on 22 Aug 2005 05:19:00 -0700
    from address [email protected]:

    >HI,


    >Phone model: Nokia 5510
    >Cable: original DKE-2 cable.


    >I read that with this cable I can ONLY upload music.


    >So I bought an FBUS cable, that connects via USB and emulates a COM
    >port.


    >With Oxygen it doesn't work, it says "COM 3: Phone is not found".


    >Can I use DKE-2 to transfer data or do I have to use only the FBUS
    >cable?



    >Thanks



    >Dario






  • Similar Threads